How to cut swanstone panels

Cut the faucet openings with a hole saw equipped with a carbide blade. Grout Free Shower and Tub Wall Surround Panels Cleveland Columbus Nationwide - Duration: 2:40. Anybody familiar with the product. My opinion is the stuff looks like something from a hotel. The clients that request this stuff are the ones I do not like to mess with.

Would you mind sharing which tool(s) you used to make cuts in the swanstone panels ? Wear protective gloves to prevent personal injury. The panels should be installed at temperatures not less than degrees. Side Splash Panel for Vanity Tops (one per carton). Shop our selection of null in the Department at The Home Depot. A hacksaw is a versatile type of saw useful for cutting a variety of materials for projects around the home.

One of the benefits of owning a hacksaw is that one blade can successfully cut metal, plastic and wood. After you measure and trim the panels , when you glue them to the walls, you need to set up a jig to keep pressure on the panels until the glue sets. Seal the sheets to the pan with silicone that matches the sheets. Make templates of the walls before you cut the swanstone and then lay the templates on the swanstone for exact cuttting.

Inspect Before Cutting Make sure no electrical wiring or plumbing is present before cutting into a wall to install any accessories. Firmly go over the entire surface with a J-roller to set the panel into the silicone. To lay out and cut the plumbing-end panel , put the cardboard template on top of the end panel and mark the locations of the holes. Remove the template and drill out the holes with a hole saw (photo 6).

Cut larger holes with a router and straight bit. Y (1 oz) for every 0square inches, or 6-tubes for an average shower. Cut the panel from the back side with a circular saw or a saber saw. Lightly sand the edge with fine or medium sandpaper to remove any rough edges. This foam spacer will help fill the gap when caulking the panel.

Then installing the swanstone over, with a bead of kerdi fix sealing the edge of the swanstone to the kerdi corner, but use the swanstone adhesive for holding it to the drywall not covered by the kerdi? It would take allot of accuracy and more time to finish the inside cut edges, but would look great without caulk showing anywhere. Using the proper cutting tools (see Cutting and Routing Tools), measure and trim as needed.

Ease (round over) the outside corners and edges of the trim strips. Fasten the trim in place by using silicone on the part of the trim that laps over the sheet on the wall, as well as to the trim that butts against the original wall. Lower cost of ownership than tile – Ceramic tile can be expensive to install and maintain with the need to reseal and regrout vs. Standard shower packages consist of a shower base with integral threshold and integral water seal lip, high wall panels and recessed soap and shampoo holders.

Custom showers are available up to x (depending the location of the drain hole). Making custom sized shower walls will be a chore also because the panels – like the Kohler line – are only available in standard sizes (they come in 36”, 48” and 60” sizes). Place pieces of masking tape over the area where the saw contacts the finished surface of the panel.

Mark those points on the end panel and cut the holes. Hole saws make the cleanest cuts, but you can also make the cuts with a sharp 1-in. Set the surround panels , locking the corners. To view all available colors from Swan, including the new Altitude Collection , click here. Cutting Hazard The installation of Swan fabrication product will.

Under Counter Vanity Sink. Any cutting , notching, drilling, or sanding can be done using regular wood cutting tools. Use a one-inch spade bit to cut the holes for the spout. Panels are attached to the wall using our adhesive silicone.

Cutting the larger hole for the faucet will likely be a two-step process. Drill a starter hole, and then use a sabre saw to cut it to size. Once the holes are cut , apply adhesives, remove the paper backing from the tape, and install the panel. With a clean rag, wipe the surface and interior edge of the pre-cut drain opening, to remove any dust or other contaminants from the pan’s drain area. Around the drain opening apply a generous bead of 1 silicone, (Fig.

5). Save swanstone shower wall kit to get e-mail alerts and updates on your eBay Feed. Note - in the DIY standard kits the trim pieces are already pre- cut. Solid Surface 1-Hole Drop and save off the $307. Save money and sharpen your DIY skills by learning how to install a solid-surface backsplash.

Cut costs while you are at it with our low prices, every day, on everything, such as large-ticket things like room furniture. If the tub, shower basin or walls are not square and level, you may need to cut or file the panels at the bottom to achieve a precise fit. Swanstone Bathtub and Shower Wall Panels.