Finishing plywood edges

How To Finish Plywood Edges Building with plywood is convenient and inexpensive, but the exposed edges typically look unfinished. To clean up the look without covering or hiding every edge , you can just cover them with a strip of self-adhesive veneer edge banding. Edge banding is a band of veneer with heat activated or pressure sensitive adhesive that is applied to the edges of the plywood. It can be trimmed using a craft knife but a cleaner cut can be achieved by using an edge banding trimmer. Screen molding can be tacked into place on the edge of plywood using a brad nailer before sanding the edges so that the plywood and screen molding transition is smooth and even.

Use a wood filler to fill the nail holes before applying any paint finish or stain. The material I chose to use is finish grade plywood. No problem, it can be covered. An ordinary electric iron can be used to apply iron-on veneer tape to the edges of the plywood.

The thin wood veneer is back-coated with a heat-sensitive adhesive. Simply lay it onto the plywood edge and press it down with a hot iron. The flexible veneer can be applied to long straight edges and to contoured pieces, such as a rounded tabletop. This is a process where a thin, narrow strip of the same type wood the plywood is made from is glued on edges so the wood looks like solid lumber instead of seeing plies of wood.

Three Ways to Finish the Edges of Plywood To me, plywood is the most economical choice of material when building furniture or cabinets. Edge Banding Solid Wood Edge Dry Dex or joint compound. Plywood is a great material for building cabinets, bookcases and shelves. But exposed edges usually look unfinished unless they’re covered with a layer of wood. While wood veneer tape is one easy way to cover edges , a better method is to glue or nail on a strip of solid wood nosing.

Position edge band so it extends a bit beyond each face of the plywood. Glue to the edge and either clamp or pin it with a brad gun. Once the glue dries, sand the edges flush with the face of the ply. Break (slightly round off) the outside edges of the solid wood to give it a finished look before painting. Unfortunately, even high-quality plywood sometimes has small voids in the edge.

Although it is harder to work with when a high degree of finish quality is paramount I like to use auto body filler (Bondo) in this and. After the glue has coole use a single cut, mill bastard file to remove the extra veneer from the edges. Hold the file at a sharp angle to the plywood when filing. Follow this with medium (1grit) sandpaper to smooth and take the sharp edge off the veneer before finishing the plywood. Watch this video to find out more.

I am planning to make a varation of CDavy’s plywood toybox. I don’t think he’s active on the site, so I thought I’d ask here. I’d just glue a strip of wood to the edge , but the curve would make it difficult. Do I just get a thin strip.

Normally I would just edge band the plywood but since I am painting this project. For a different look, I want to keep the edges expose so you can see the plys. Tip: With exterior plywood , it is extremely important to finish the edges with great care, since plywood is a composite woo and if water leaches into the edges , it can cause quick mold and rot. Many Types of Plywood for Any Job. Re: Painting plywood edges ? The shellac based stuff lets you get more coats on faster so you can sand something substantial enough to hide the grain sooner.

Plywood Edges and Glue - Finishing Tip By Alan Noel Professional Wood Finisher When building a project out of plywood , one of the things you have to consider is how to deal with the edges of your material. Plywood edges aren’t the prettiest thing to look at, and can make a woodworking project scream “homemade. There are a few different ways to hide plywood edges , but my favorite is edge banding. This simple finishing technique makes clean edges that give your project a professional look.

Plywood , just like any other woo requires preparation before painting. The quality of the preparation determines the finished quality of the painted surface. If you start with furniture or.

You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. Another method of finishing exposed plywood edges is to cover them with shelf edge , a type of thin, narrow molding. The molding, which is attached with glue and brads, gives a decorative edge.

There are 5finishing plywood edges suppliers, mainly located in Asia. The top supplying countries are China (Mainland), Singapore, and India, which supply , , and of finishing plywood edges respectively. The open edge of plywood makes a really fun style, but if you’d like a more finished look, there are main ways to finish plywood edges. Finishing plywood edges products are most popular in North America, Oceania, and Central America. Covering Plywood Edges and Surface Finishing.

IF the plywood looks nice, I would put a finish on it. Whether you use shellac or varnish or poly is more of a. Incorporating Uncovered Plywood Edges Into Design Written by Scott LeGros The rough edges of plywood that show off the wood’s composite composition are often covered up with veneer and edging to produce a neat, polishe “finished” look. So the first question you need to ask yourself is, which one do you want to use.

The goal is not to sand the filler away but to even it out and fill the open pores of the end-grain plys.