How to cut formica countertop

Often the appliance or item to be installed in the new hole will have a flange or rim which will conceal the cut edge of the opening. If the edge of the opening will not be concealed a router with a special bit will work well and minimize. Formica always cut from the back side. After you build the counter top, it must be clean with no waves or holes.

Remove any masking tape used for the larger cuts with the circular saw. Your circular saw may come with a “ rip fence,” which is a T-shaped guide that you can use for your cut. You can buy laminate countertops in stock sizes that come in two foot intervals between and feet. Again, use masking tape where you will be cutting to protect from chipping. The manufacturer of your sink.

This video shows how to cut a laminate countertop. The instructions on this video shows a degree, STRAIGHT CUT. If you are needing to miter a degree angle, I have anther video for that on my. The procedure of cutting formica countertops is as explained below.

A sawhorse is used as a platform or base for cutting countertops out of formica. A circular power saw with teeth is ideal for cutting these countertops. Most of the cutting is done with power saws, while the finishing is carried out with a power jigsaw.

If not backsplash another option is to cut wide with the circ saw and follow up with a router and a trim bit. Will need a fence since will not be able to use the edge to guide the bearing. I plan on buying the pre formed formica countertops sold at Home Depot for $1per ft. Best Countertops for section rentals. Replace Countertops for Rental?

Cut a Piece of Plastic Laminate Countertop Get Perfect Miter Joints on Laminate Countertops When installing a laminate counter top two things seem to happen. How to Cut Laminate Counter Tops Cutting Laminate Counter Tops to Length. Measure the length needed for the counter top at multiple points with a tape measure.

Lay a counter top on a stable surface with the laminated side facing down. Align the inside edge of a circular saw blade with the. Measure your installation face side to side and front to back with a tape measure.

Lay your laminate out on a stable work surface, with its backing face up for marking. Best way to cut a formica countertop Hi- we bought a prefab formica countertop and it is slightly oversized. We are trying to figure out the best way to cut it down, it does have a backsplash on it. The bit should have a bearing on the end so you can easily follow the contours of the countertop while cutting.

The tool should be operated so that the leading edge of the bit bites into the material. Use your straightedge and utility knife to cut along the line as accurately as possible. Use the utility knife first, as it will provide a goo clean cut. To cut through laminate countertops , you can use a hand saw, but a circular saw makes the job much quicker.

Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front. It has evolved over the years to include more than just countertop covering. However, cutting the product has not changed. To get the best possible cut requires clamps, straightedges and sharp router bits.

The type of bit to be used depends on the reason for the cut. Use a fine-tooth handsaw (to point) and always cut into the laminate surface to avoid chipping. Before making any more cuts, the cut -out formica shape you already have should be set on the designated surface and properly installed.

Contact cement is typically used for this. Place the formica face down on any surface, and cover the back with contact cement. A large paint brush helps spread it out evenly. I can easily remove a short section of cabinetry below the countertop but how can I cut off the 3. The countertop has the backsplash attached and has the rounded waterfall face. A laminate countertop installation is basically a grade-school cut -and-paste project writ large.

You build the substrate, cut out the laminate, and paste the two together with contact cement. Countertops installed by the professional contractors at The Home Depot. In this video, Jeff Johnson from Glen Allen, Va.

Unfortunately, any laminate countertop surface can be cut by sharp knifes, accidentally scorched by hot pans, or chipped.